DS1721U+T&R【PDF 10/17 页】IC THERMOMETER/STAT DIG HP 8USOP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录39

6页 7页 8页 9页 [10页]11页 12页 13页 14页

DS1721

10 of 17

SLAVE ADDRESS

A control byte is the 1

byte received following the START condition from the master device. The

control byte consists of a 4-bit control code; for the DS1721, this is set as 1001 binary for read and write

operations. The next 3 bits of the control byte are the device select bits (A2, A1, A0). They are used by

the master device to select which of eight devices are to be accessed. The set bits are in effect the 3 least

significant bits of the slave address. The last bit of the control byte (R/

W ) defines the operation to be

performed. When set to a 1 a read operation is selected, and when set to a 0 a write operation is selected.

Following the START condition, the DS1721 monitors the SDA bus checking the device type identifier

being transmitted. Upon receiving the 1001 code and appropriate device select bits, the slave device

outputs an acknowledge signal on the SDA line.

COMMAND SET

Data and control information is read from and written to the DS1721 in the format shown in Figure 6. To

write to the DS1721, the master will issue the slave address of the DS1721 and the R/

W bit will be set to

"0". After receiving an acknowledge, the bus master provides a command protocol. After receiving this

protocol, the DS1721 will issue an acknowledge and the master may send data to the DS1721. If the

DS1721 is to be read, the master must send the command protocol as before then issue a repeated START

condition and the control byte again, this time with the R/

W bit set to "1" to allow reading of the data

from the DS1721. The command set for the DS1721 as shown in Table 4 is as follows:

Read Temperature [AAh]

This command reads the last temperature conversion result from the Thermometer Register in the format

described in the OPERATION-Measuring Temperature section. If ones application can accept

thermometer resolution of only 1.0癈, the master only must read the first data byte and follow with a

NACK and STOP. For higher resolution, both bytes must be read.

Access TH [A1h]

If R/

W is "0", this command writes to the TH register. After issuing this command, the next 2 bytes

written to the DS1721, in the format described for thermostat set-points, will set the high temperature

threshold for operation of the TOUT output. If R/

W is "1", the value stored in this register is read back.

Access TL [A2h]

If R/

W is "0", this command writes to the TL register. After issuing this command, the next 2 bytes

written to the DS1721, in the format described for thermostat set-points, will set the high temperature

threshold for operation of the TOUT output. If R/

W is "1", the value stored in this register is read back.

Access Config [ACh]

If R/

W is "0", this command writes to the configuration register. After issuing this command, the next

data byte value is to be written into the configuration register. If R/

W is "1", the next data byte read is the

value stored in the configuration register.

Start Convert T [51h]

This command begins a temperature conversion. No further data is required. In one-shot mode, the

temperature conversion will be performed and stored and then the DS1721 will remain idle. In continuous

mode, this command will initiate continuous conversions.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式